Skip to content

Dog Kennel Wall Liner


SKU LV-18-30-100

Our dog kennel wall liner is designed to protect drywall from overspray in dog washing areas. The thick, durable plastic is waterproof and constructed from HDPE. The material provides excellent dimensional stability and a high level of durability. The plastic is best attached to drywall using screws and washers (not included). The dog kennel wall liner is available in roll widths ranging from 18” to 60” and in 100’ lengths. The liner is also available in varying material thickness from 40 mil to 100 mil. Under standard dog washing environments the 40 mil is adequate for wall protection. Covering a large area is possible with multiple sheets overlapped at the seams.

The HDPE plastic is UV stabilized and made in the USA.


*The widest HDPE roll that we offer is currently 5’ (60 inches).

Please note that we are unable to provide custom roll lengths.

Plastic Sheeting

  • Material: High Density Polyethylene
  • Texture: Smooth
  • Size: Various
  • Need a Written Quote? Request Online >
  • Volume Pricing on Orders $6,500+
  • Questions? Call (800) 621-5381

Product Features

  • Waterproof
  • Commercial Grade
  • UV Resistant
  • Will Not Rot or Mildew
  • Non-Biodegradable
  • Non-Resistant to Rodent and Insect Damage
  • 100 Year Material Lifespan
  • Made in the USA


When installing with a chain link or wire fence:

  • Start by cutting the liner to fit your area
  • Choose and end to start with and drill 2 holes in the liner greater than the width of the wire you are attaching it to and at least one inch from the edge. (This can be reinforced with grommets if needed)
  • Insert a zip tie from the backside of the wire and loop it through the hole and then back through and secure it on the backside every 12"
  • Then repeat the same on the bottom and around the entire wall every 12”
  • Once completed use flush cuts to cut off the excess zip ties and remove any sharp edges

When installing on a solid wall:

  • Start by cutting the liner to fit your area
  • Choose one side to start on and screw to the wall using a roofing screw so it has the waterproofing shank attached to it
  • Screws should be installed top screw, and then bottom screw all the way around the wall every 6" to 12" to help minimize any bubbling
  • In corners where there is a seam (if applicable) it is best to use a waterproofing tape or mastic underneath the barrier and on top of it as well to prevent any water or urine intrusion

Cleaning as needed using warm water and a drop of dish soap if needed. A cotton or microfiber towels works best.

Connecting HDPE Pieces

There are two ways to connect multiple pieces of HDPE together. One method is to overlap the HDPE and use our double sided seam tape to connect the two pieces. The other method is to butt the ends together and use our 17 mil single sided seam tape to create a solid connection.


Overlap Method
(for underground installations)

The overlap method is best used when connecting two pieces of HDPE in a buried application. Due to the overlap, a ridge is exposed which is not ideal when installed in exposed vertical or flat installations in high traffic areas as there is a possibility of an object catching on the ridge and pulling the two pieces apart.

In a below ground installation, the large overlap area provides a more water resistant connection as well as enhanced protection against tree and plant root intrusion.

View Tape Pricing and Seaming Instructions >

End to End Method
(for exposed installations)

When installing HDPE on a wall, floor or anywhere that is exposed, the end to end method provides a secure connection and does not leave any ridges exposed to potential catching by a person or object.

View Tape Pricing and Seaming Instructions >


  • Ships Free (standard ground, see map)
  • Expedited shipping only available on orders over $2,000

Shipping estimates shown on the map pertain to this specific product only. HDPE orders typically ship same day if the order is placed before 12:00 noon CST. Transit times displayed in the map are listed in business days, and are approximate. Transit times are subject to stock levels at regional warehouses. The day that the order is shipped is not counted as a transit day.

Thickness comparison

The below is a thickness comparison of the material. HDPE plastic thickness is measured in "mils" which is "thousands of an inch".

HDPE Barrier Tape - Moisture Resistant
HDPE Barrier Tape - Moisture Resistant
HDPE Barrier Tape - Moisture Resistant
HDPE Barrier Tape - Moisture Resistant
HDPE Barrier Tape - Moisture Resistant
HDPE Barrier Tape - Moisture Resistant

HDPE Barrier Tape - Moisture Resistant