LV · TURF ACCESSORIES IN STOCK · SHIPS FREE

Artificial Turf Accessories

The seaming and anchoring supplies that make synthetic turf installs look factory-finished — professional-grade adhesive, seam tape, and turf nails from SRW Products.

SEAMING

Tape + adhesive

ANCHORING

5″ / 6″ nails

BRAND

SRW Products

SHIPPING

Free · nationwide

A synthetic-turf installation is only as good as its seams and anchoring. These SRW accessories cover both: high-viscosity Seams Right™ turf adhesive and high-strength seam tape for invisible, durable joins, plus bright-steel and galvanized turf nails that lock the perimeter and field down tight.

Below you'll find how to choose between tape and adhesive, how to space and drive turf nails, a step-by-step seaming workflow, and the field practices that keep seams flat and edges secure for years.

What You Need for a Clean Turf Install

Seam tape

A high-tensile fabric backing that bridges two turf edges. Adhesive is applied to the tape, and both turf panels are pressed onto it for a strong, invisible seam. Best for long runs and DIY-friendly installs.

Turf adhesive

High-viscosity, weather-resistant adhesive that bonds turf backing to seam tape (or turf-to-turf). Cures to a flexible, durable joint that holds up outdoors in heat and cold.

Turf nails

Bright-steel or spiral-galvanized nails that anchor the turf perimeter and field to the base. The spiral galvanized nail resists pull-out and corrosion for long-term hold in exposed installs.

Seaming: Tape & Adhesive

Seam tape + adhesive (recommended)

Roll seam tape under the joint (shiny/printed side down), apply adhesive in an even S-pattern across the tape, then fold both turf edges down into the wet adhesive and press. This is the standard method for a strong, hidden seam on most residential and commercial installs.

When to size up the tape

Standard 6″ tape suits most straight seams. Step up to 12″ tape for high-traffic areas, heavy pets, or wide seams where extra bonding surface and stability matter. Tape comes in 6″×100′, 12″×50′, and 12″×100′ cartons.

Rule of thumb: tape provides the bonding surface, adhesive provides the bond. Used together they create a seam that's strong, flat, and invisible — neither one holds reliably outdoors on its own.

Anchoring & Nailing

Perimeter first

Nail the full perimeter every 3–4 inches so edges can't lift or curl. Keep nails just inside the edge and tuck fibers over the head so it disappears into the pile.

Then the field

Anchor the interior on a grid, roughly every 12–24 inches depending on traffic and base firmness. Add nails along seams to keep the joint flat.

5″ smooth vs 6″ spiral

The 5″ smooth bright-steel nail drives fast for general use. The 6″ spiral galvanized nail bites harder and resists pull-out and rust — the better choice for exposed, high-traffic, or long-term installs.

Protect the fibers

Drive nails flush, not over-set. Use a rubber mallet for the final seat and brush the pile back up over the head so no metal shows at the surface.

How to Seam Artificial Turf (Step by Step)

Dry-fit and trim the edges

Butt the two turf panels together without overlap. Trim 2–3 stitch rows off each factory edge so the seam meets tuft-to-tuft, and make sure the grain (pile direction) runs the same way on both panels.

Fold back and lay the tape

Fold both edges back and center seam tape under the joint, shiny/printed side down. For a 6″ seam, roughly 3″ of tape sits under each panel.

Apply the adhesive

Run a generous, even S-bead of turf adhesive across the tape, then spread it to a uniform layer with a trowel. Work in manageable sections so the adhesive stays wet as you set the turf.

Set and press the seam

Fold both edges down into the wet adhesive, keeping tufts tight together with no adhesive on the fibers. Press along the seam and weight it (boards or sandbags) while it sets.

Nail the seam and perimeter

Once the seam is set, add nails along the joint to keep it flat, then anchor the full perimeter every 3–4 inches and the field on a grid.

Brush and infill

Power-brush the pile to stand it up and blend the seam, then apply infill as specified for your turf to weight it down and support the fibers.

Best Practices (and Common Mistakes)

Match the pile direction

Turf has a grain. Seaming two panels with the pile running opposite directions makes the seam show in every light. Confirm direction before you glue.

Don't get adhesive on the fibers

Adhesive belongs on the backing and tape, never the blades. Glue on the fibers stiffens the pile and creates a visible, crusty line.

Weight the seam while it cures

Seams fail when they're walked on before the adhesive sets. Weight the joint and keep traffic off until it's cured per the adhesive's instructions.

Anchor tighter in high-traffic zones

Widen your nailing pattern for pets, play areas, and entries. Under-nailed perimeters are the most common cause of lifting edges.

Frequently Asked Questions

Do I need both seam tape and adhesive?

For a proper turf seam, yes — the tape provides the bonding surface and the adhesive creates the bond. Together they make a seam that's strong, flat, and hidden. Tape or adhesive alone won't hold reliably outdoors.

How much adhesive and tape will I need?

Plan tape by the total linear feet of your seams (plus a little overlap), and adhesive by coverage per tube across that tape. Seam tape comes in 6″×100′, 12″×50′, and 12″×100′ cartons; adhesive ships as 28 oz tubes by the carton. Send your seam footage for help estimating.

Which turf nails should I use?

The 5″ smooth bright-steel nail is a fast general-purpose fastener. The 6″ spiral galvanized nail resists pull-out and corrosion, making it the better pick for exposed, high-traffic, or permanent installs. Many installers use 6″ on the perimeter and 5″ in the field.

How far apart should turf nails go?

A common approach is every 3–4 inches around the perimeter and along seams, with field nails on a 12–24 inch grid. Tighten the spacing in high-traffic areas, for pets, and on softer bases.

Will these work for pet turf and play areas?

Yes. For heavy pet or play use, step up to wider 12″ seam tape and tighten your nailing pattern so seams and edges stay put under extra traffic and cleaning.